DuPont WFQT130005 Instruction Manual download pdf (Page 9)

STEP 8

Test the Filter System for Proper Operation (continued)

If there are leaks on the Kitchen Faucet Adapter connection:

n Turn off the cold water shut-off valve to the Filter System to release pressure in the System.

n Locate the Kitchen Faucet Adapter.

• If the 1/4" Plastic Tubing is leaking, follow the previous steps (“If there are leaks around the fittings”).

• If the thread between the Kitchen Faucet Adapter and the kitchen faucet stem is leaking, tighten more securely. If leaking

continues, disconnect the 1/4" Plastic Tubing and remove the Kitchen Faucet Adapter. Wrap the Kitchen Faucet Adapter

and the threaded faucet stem with plumber’s tape and re-install (see Step 2 of Installation Instructions).

• If the thread between the Kitchen Faucet Adapter and the cold water supply line is leaking, tighten more securely. If leaking

continues, disconnect the 1/4" Plastic Tubing and remove the Kitchen Faucet Adapter. Wrap the Kitchen Faucet Adapter

and the cold water supply line with plumber’s tape and re-install (see Step 2 of Installation Instructions).

n Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.

If there are leaks on the Faucet for Filtered Water/1/4" Plastic Tubing connection:

n Turn off the cold water shut-off valve to the Filter System to release pressure in the System.

n Loosen and remove the Compression Nut

K on the Faucet for Filtered Water Stem. Check the 1/4" Plastic Tubing to see if it is

cut squarely. Make sure the 1/4" Plastic Tubing is placed firmly into the end of the Faucet Stem; retighten the Compression Nut

securely by hand; then tighten 1/2 turn with an adjustable wrench. If leaking continues, remove the Compression Nut and apply

plumber’s tape to the Faucet for Filtered Water Stem and re-install the Compression Nut.

n Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.

‰ If leaks continue, turn off the water supply and call Customer Service or your local plumber.

‰ For Filter Replacement Instructions please see below

QuickTwist

™

Filter Replacement

1 Turn off the cold water shut-off valve to the Filter System A.

2 Turn the QuickTwist

™

Filter B clockwise until it releases. Gently pull down on the used QuickTwist

™

Filter to remove it from the

System Head. Discard the used QuickTwist

™

Filter.

NOTE: Place a pan or bucket under the Filter System to catch any water drips.

3 Hold the new QuickTwist

™

Filter with the label facing to the left slightly. The two nozzles on top of the QuickTwist

™

Filter should

be toward the back of the QuickTwist

™

Filter. If holding properly, the two extended flanges on top of the QuickTwist

™

Filter should

be out to each side.

4 Lift the QuickTwist

™

Filter straight up into the System Head until the two nozzles seat into the ports and the two extended

flanges on top of the QuickTwist

™

Filter are fully engaged into the System Head.

5 Turn the QuickTwist

™

Filter counter-clockwise until it stops.

6 Turn on the cold water shut-off valve and the Faucet for Filtered Water D and check for any leaks. If there are leaks, refer to the

troubleshooting information in Step 7 of the Installation Instructions.

7 Flush water through the Faucet for Filtered Water for approximately 10 minutes to flush out any air and carbon fines

(fine black powder) from the QuickTwist

™

Filter. Check for leaks once more before completion.

V4.0

WFQT13000 & WFQT13500 Series

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Comments to this Manuals

No comments

DuPont WFQT130005 Instruction Manual Page 9

Comments to this Manuals